instruction sheet 1 of 3 ? 2015 te connectivity family of companies all rights reserved *trademark te connectivity, te connectivity (logo), and te (logo) are trademarks. other logos, product, and/or company names may be tra demarks of their respective owners. product information 1 - 800 - 522 - 6752 this controlled document is subject to change. for latest revision and regional customer service, visit our website at www.te.com . 408 - 32222 11 dec 15 rev a removal kit numbers will remove product part numbers 2215042 - 1 6 pair x 3 col receptacles 2187540 - 1 2215042 - 2 6 pair x 3 col receptacles figure 1 1. introduction removal kits 2215042 - [ ] are designed to remove strada - whisper receptacles from printed circuit (pc) boards. refer to figure 1. read and understand these instructions before using the removal tools. 2. description each kit consists of two clamp subassemblies, a pusher subassembly, a guide module pusher plate, two pusher plate shims, and four pusher plate mounting screws. the clamp subassemblies consist of a front clamp plate, a rear clamp plate, and a clamp knob. the pusher subassembly consists of a top plate, two pusher plates, and a removal knob. the clamp subassembly clamps the receptacle while the pusher subassembly removes the receptacle from the pc board. the guide module pusher plat e is used when the receptacle is adjacent to a guide module, and the pusher plate shims are used depending on the width of the receptacle. 3. operation 3.1. tool preparation to prepare the removal tool, know the dimension of the receptacle (number of rows and colu mns) and the placement of the receptacle (what is next to the receptacle). once these conditions are determined, the tool can be prepared to remove the receptacle. to prepare the tool: 1. select the kit part number to be used based on the receptacle part numb er or size. 2. select the proper clamp subassembly for the receptacle part number or size. 3. determine if shims are necessary and install as needed. see figure 2 for shim placement. 4. select the proper side pusher plate orientation, or select the guide module pus her plate, and install the side pusher plates. refer to figure 2 for pusher plate orientation. removal kits 2215042 - [ ] for strada - whisper* receptacles original instr uctions removal knob pusher plate clamp knob front clamp plate
408 - 32222 rev a 2 of 3 figure 2 a. if a receptacle is located next to the clamp assembly, the pusher plate must have a horizontal orientation. b. if a printed circuit (pc) board is located next to the clamp assembly, the pusher plate must have a vertical orientation. c. if a guide module is locat ed next to the clamp assembly, the guide module pusher plate must be installed. 3.2. removal procedure caution be certain the removal tool assembly does not contact any components on the pc board during use. 1. loosen the clamp knob on the clamp subassembly if ne cessary to fit over the receptacle. 2. place the clamp subassembly over the receptacle and center it on the receptacle. 3. tighten the clamp knob to clamp the receptacle. hand tightening should be sufficient. see figure 3. figure 3 4. place the pusher subassembly over the clamp subassembly. (figure 4). 5. tighten the removal knob to remove the receptacle from the pc board. vertical pusher plate orientation horizontal pusher plate orientation rear clamp plate front clamp plate clamp knob
408 - 32222 rev a 3 of 3 figure 4 note the tool and receptacle can spin after removal due to the twisting action of the removal knob. this spin could cause damage to the pc board. hold the tool firmly during removal. 6. remove the receptacle from the tool by loosening the clamp knob. 4. m aintenance and inspe ction te connectivity recommends that the tool be inspected immediately upon its arrival to ensure that it has not been damaged during shipment. 4.1. daily maintenance it is recommended that each operator be made aware of, and responsible fo r, the following steps of daily maintenance: ? remove dust, moisture, and other contaminants with a clean, soft brush, or lint - free cloth. do not use objects that could damage the tool or any of its components. ? when the tool is not in use, store it in a clean, dry area. 4.2. periodic inspection regular inspections should be performed by quality control personnel. a record of scheduled inspections should remain with the tool or be supplied to personnel responsible for the tool. the inspection frequency should b e based on the amount of use, working conditions, operator training and skill, and established company standards. 5. replacement and repa ir for customer repair service or to order replacement parts, call 1 - 800 - 522 - 6752, or fax your purchase order to 717 - 986 - 7 605, or write to: customer service (038 - 035), tyco electronics corporation, po box 3608, harrisburg, pa 17105 - 3608. 6. revision summary ? initial release of document pusher subassembly clamp subassembly
|
